May
6

How To Fix A False Overheating PS3 (Heat Sensor)

Posted by Debankur Banerjee Comments (11)

How To Fix A False Overheating PS3

Go to your local radio shack, pick up some non-spill flux, apply it around the two main chips like i do in the video and then your ps3 should function correctly.(video Rating: 3 / 5)

I did this because my PS3 would think it’s overheating but really be cold to the touch. So I did this and it worked.

PS3 Overheating Solutions – How to Solve PS3 Console Overheating Problem?

Ps3 overheating solutions are incredibly important, especially if you are gamer. The problem with the Ps3 is that it tends to overheat way too much. The bigger problem is that it has an exclusive game library that you cannot find on any other console.

how to fix a false overheating ps3 heat sensor

False Overheating PS3

This isn’t the first time that something of this nature has happened. It is in fact very common for a console to fail in this manner, and just about every new generation has experienced it. Even the original Nintendo went through these problems, as well as the original Playstation.

You know the different causes, but do you know how to go about fixing your broken Ps3?

How do you get back to the games that you love so much without paying huge amounts of money for the ps3 overheating solutions?

How you are going to find solutions for Ps3 overheating is totally up to you, but there are a few simple things that you could try. In order to assist you, we will present you with a list of solutions that you could try. Keep in mind that what works for others might not work for you, but these are fairly universal and should work for any console.

Remember that a towel is never a viable solution.

VISIT >> clickable link

 

critical privacy protection

YOUR PRIVACY PROTECTION

7 Step Procedure To Fix PS3 Yellow Light of Death And PS3 Red Light of Death

The PS3 Yellow Light of Dead (or YLOD) and the PS3 Red Light of Death are probably 2 of the most common faults afflicting the PS3 console.

In this article I will briefly explain the sequence of indicator lights on the PS3 console that you need to look out for that confirms that your console is suffering from the Yellow Light of Death or the red indicator fault; why these faults occur in the first instance; and how to effectively mitigate, avoid or troubleshoot your way out of a potentially catastrophic failure of your game system that can end up costing you at least a couple of hundred dollars to fix.

It’s unfortunate but true, PS3 faults are a common occurrence with the blinking Yellow Light fault probably being the most serious and widespread problem. It is thought that many of the problems occurring with the PS3 console is largely due to a design flaw, making it vulnerable to failure.

PS3 Yellow Light of Death

If the power status light on your console flashes or blinks from green to yellow and back to green, this is known as the “yellow light of death”. If what you experience is a power status light that flashes red after using your console for 3 or more minutes and then shuts down, then you are likely to be experiencing the red light of death.

It’s widely believed that the main cause of the Yellow Light of Death is due to the processor getting so hot during heavy use of the console that the tiny solder points on the GPU liquefies and over time loses its connection with the motherboard.

Can the PS3 YLOD be fixed with a hair dryer

How to fix a false overheating PS3 ( heat sensor ) – Duration: 7:20. UB3Rgaming 293,045 views. 7:20. How to fix a hard YLOD error on your PS3 FAT&SLIM Models By:NSC – Duration: 34:14. UltraNSC 139,997 views. 34:14. PS3 Flashing Red Light Repair …

Older PS3s tend to be more vulnerable to YLOD and it’s believed that this may be due to them having older less efficient processors that generate more heat than the newer PS3 models. The official line from Sony however is that the yellow indicator warning light can be caused for a variety of reasons, without giving any further explanation

What we do know from the many PS3 owners that have experienced the YLOD fault is that the only repair that seems consistently to work involves opening up the PS3 console and using a heat gun to heat up the CPU / GPU and direct chipsets.

However, in a limited number of cases, the YLOD warning may be due to a faulty power supply preventing the console from properly booting up. To determine what is causing the YLOD, switch the console off and allow it to cool down for at least 20 minutes. Then turn the console on and listen closely for the fan. If the fan powers on briefly and then switches off again, you are likely to have a problem with the motherboard. If you don’t hear the fan on start-up, then the likely problem is with the power supply.

The red light error may also be caused by overheating but equally it may also be because of a major hard drive failure. Depending on how often you use your PS3 and how well you look after it, a hard drive ought to last on average at least 3 to 5 years.

Download PlayStation Subscription Now(image link)

Of the two YLOD is the more serious as it tends to indicate an internal fault needing a professional repair. A flashing red indicator light on the other hand is often the precursor to more serious internal problems. So if you are experiencing a red warning light, all is not lost. In fact even if you are getting a yellow warning light, you may still be able to recover you PS3 system if you catch it early enough.

Since we know that many of the problems that arise with the PS3 are due to overheating especially if the console is being used for long periods of time, here are some of the things that you can do to prevent serious damage:

custom search

Your Friends Need This
Share
Categories: Error Fix Laptop

11 Responses to “How To Fix A False Overheating PS3 (Heat Sensor)”

  1. UB3Rgaming says:

    @Paul Short just long enough to melt the flux. You have to let it sink
    under the chips.

  2. Stig Brännlund says:

    So many errors, this sure is a hobbyist solution :P.

    Bad method of applying AS5 (according to themselves – you should only have
    a thin line applied…) – Also MX-4 is better since it doesnt need any
    curing and its also NOT electrically conductive,

    Flux (which are really actually only used to “eat” oxygen when soldering)
    needs higher temperature to melt properly then what a hairdryer can provide
    :P, also some kinds of Flux are corrosive and will damage the connections
    overtime!.
    Also! dont use flux on top of the chip like i saw in the movie 😛

    Working on a rug?! omg you will get ESD problems and lint into the paste.

    If this seems to work its probably just because the Flux is spreading heat
    away from the chip onto the PCB and probably lowers the temperature reading
    due to the temperature spread. When the flux hardens/evaporates when the
    chip goes hot again (and by age) i can bet the issue comes back again.

  3. UltraNSC says:

    OMG are u kidding??? this is not the Sensor, you have this Problem because
    your Thermal Compound INSIDE the IHS is old and bad. Cut the IHS and apply
    new Thermal paste and have fun !!! More on my Channel !!!

    /: GUYS DONT FUCKING DO THIS : and if you do this, use Flux and a Heat Gun
    >WTF< and apply NEW THERMAL PASTE !!! 

  4. Oscar Tejeda says:

    Damn ps3, only lasted me 8 years!!

  5. deth502 says:

    guys, y all the hate? all the negative comments about not enough heat to
    melt the solder, wrong flux, carpet static, not cleaning the old paste,
    ect.

    those are all moot points. its still not going to work for shit because he
    never plugged the fan back in. 

  6. Teknogod17 says:

    omg is that a hair dryer. just fucking Christ people.

  7. William Mitchell says:

    This video takes things to a whole new level of retard.

  8. A Wild Otter Appeared! says:

    Sir, my hats off to you for reaching new a whole new level of stupidity for
    a very very amateurish attempt at fixing electronics. If you had an idea of
    what you’re doing you wouldn’t disassemble a goddamned piece of electronic
    device on a carpet! Because even if you have an anti-static case place
    under the PS3 the static can be transmitted through your body which can
    result in frying the motherboard!

    I’m wondering how many circuit boards have died because of your stupid
    decisions?

    EDIT: Did you just forgot to wipe off the old paste? What an idiot!

  9. beankiller4ever says:

    Let this guy fix the overheating is like giving a gun to a retard!

  10. lukesheridan1992 says:

    you do know if you just slapped the console about 10 times it would have
    knocked the “sensor” and unstick.

  11. videogamegeek RAYGAH says:

    question. what wattage hair dryer is safe?

Leave a Reply